Cakewalk // Documentation // SONAR LE // Audio - Sync and Caching (Advanced)
Table of Contents Previous Next Index

Dialog box referencePreferences dialog ► Audio - Sync and Caching (Advanced)

The Sync and Caching section lets you specify audio synchronization and hard disk cache settings.
The Sync and Caching section contains the following settings:
list-image
Trigger and Freewheel. With this option audio playback starts (or triggers) at the exact timecode, but then the audio plays at its own internal rate. The audio can gradually drift away from SMPTE time due to variations in the timecode signal.
list-image
Full Chase Lock. With this option the speed of audio playback is continuously adjusted to stay with the timecode.
list-image
Timing Offset (msec). With this option, used for making very fine adjustments to the audio/MIDI synchronization of your project, you can offset the audio in your project by a number of milliseconds. A positive value delays audio by that amount. A negative value delays MIDI by that amount.
list-image
When SMPTE/MTC timecode is detected. This option tells SONAR what to do when it detects SMPTE/MTC timecode. Choose from the following:
list-image
Ask first, then switch to clock source and start. This option prompts SONAR to alert you when it detects a SMPTE/MTC signal, asks if you want to sync to the incoming signal, and if you respond that you do, switches the clock source and starts to receive the signal.
list-image
Always switch the clock source and start. SONAR automatically switches to the clock source of the incoming signal and begins to receive the signal.
list-image
Do not switch clock source, but start if in SMPTE/MTC mode. This option automatically syncs to the incoming signal if SONAR is in SMPTE/MTC mode.
list-image
Never switch clock source, never start. SONAR does nothing when incoming SMPTE/MTC timecode is detected.
Note: The final option, Never switch clock source, never start, should never be used if you are attempting to sync to an external clock source.
list-image
When clock source is set to SMPTE/MTC or MIDI Sync, pressing play in SONAR will. This option tells SONAR what to do when you press play in SMPTE/MTC or MIDI Sync mode:
list-image
Switch current clock source and start playback. Switch the clock to Audio (from SMPTE or Sync), and start playback. This cancels SMPTE (or Sync) mode.
list-image
Maintain current clock source and wait for timecode. Do not switch the clock (Stay in SMPTE or Sync mode), but wait for SMPTE or Sync. The playback button remains depressed.
list-image
Enable Read Caching and Enable Write Caching. Choosing either of these options lets SONAR use the Windows disk cache while reading or writing audio data. SONAR will usually perform best with all caching disabled, which is the default setting. If your computer has an older IDE disk controller, or a disk controller that does not use DMA transfers, enabling caching may improve SONAR’s audio performance.
list-image
I/O Buffer Size. This value determines the buffer characteristics for transfers to and from the disk. Changing this value does not affect audio latency, but will affect the disk throughput for audio tracks. The default setting is 128. A higher value causes more audio to be buffered from the disk ahead of the playback cursor. If you are hearing consistent dropouts/clicks in your audio and if your project contains high bit depth (32/64 bit) or high sample rate audio (88.2K or higher), it may be indicative of a too small I/O buffer size. If so, try a higher I/O buffer size like 256 or 512. If audio problems persist, reset to 128 and try a different remedy.
If you use ASIO mode, enter 0 in the Manual Offset field and leave the Reported Input Latency check box checked (this check box only appears in ASIO mode). This will line up audio in most cases. If you think you can tweak it closer, use the Manual Offset field.
Copyright © 2024 Cakewalk, Inc. All rights reserved
Sitemap | Privacy Policy | Legal